Exam Focus
- Keep the faucet out of contact with glass and beer.
- Open the tap fully.
- Fill the glass about three-quarters down the side.
- Allow the beer to settle for 1 to 2 minutes.
- Finish down the middle for appropriate head.
What makes nitro different
Nitro beers are pushed with a CO2-nitrogen blend that is mostly nitrogen and poured through a special faucet with a restrictor plate, a small disk with tiny holes. Forcing beer through the plate knocks gas out of solution as a cascade of very small bubbles. Nitrogen dissolves poorly in beer, so those bubbles stay small and build a dense, creamy, long-lasting head and a smooth texture. The swirling cascade is normal, not a fault.
Step by step
Follow the same hygiene rules as any draft pour, then add a settling pause.
- Never let the faucet touch the glass or sit in the beer or foam.
- Hold the glass at a 45-degree angle, about 1 inch (2.5 cm) below the faucet.
- Pull the tap handle forward to the fully open position.
- Pour down the side until the glass is about three-quarters full, then stop.
- Let the beer settle for 1-2 minutes.
- Pour down the middle to finish with an appropriate head.
Compared with a standard draft pour
| Step | Standard draft | Nitro |
|---|---|---|
| First fill | About two-thirds, down the side | About three-quarters, down the side |
| Pause | None; straighten the glass and keep pouring | Settle for 1-2 minutes |
| Finish | Down the middle as the glass straightens | Down the middle after settling |
| Head | About 1 inch for most beers | Dense, creamy, fine bubbles |
Other Certification Notes
Certified Cicerone® Open the Certified Cicerone® topic page
Exam Focus
- Explain nitrogenated texture and cascade formation.
- Use correct glass and pour technique for nitro beer.
- Recognize when poor cascade suggests gas, faucet, or temperature issues.
Reading a bad cascade
A good nitro pour shows a tight, slow cascade of fine bubbles and settles to a dense, creamy head. When it does not, the cause is usually gas, faucet, or temperature.
| What you see | Likely cause | Check |
|---|---|---|
| Weak or no cascade, thin head | Too little nitrogen in the blend, low pressure, or missing restrictor plate | Gas blend and regulator; faucet parts |
| Large, coarse bubbles | Too much CO2 in the blend or a worn restrictor | Blend and restrictor condition |
| Sputtering, spitting flow | Dirty or partly blocked restrictor | Disassemble and clean the faucet |
| Excess foam, little liquid | Warm beer or warm tower | Beer temperature at the faucet |
Nitro faucets must be fully taken apart and cleaned during every line cleaning, because the small restrictor holes clog easily. Keep the nozzle out of the beer and foam on every pour, and hold the glass about 1 inch (2.5 cm) below the faucet.
Worked application
Nitro beer relies on nitrogenated dispense and a restrictor faucet to create dense foam and a cascading presentation. The pour often requires a proper glass and enough settling time. If the cascade is weak, flat, or violently foamy, the likely causes include gas blend, restrictor condition, temperature, or beer formulation rather than ordinary CO2 technique.
Why It Matters
- Nitro beer needs its characteristic pour and settling sequence to build a dense head.
- Recognizing normal cascade behavior prevents staff from treating it as a standard CO2 dispense problem.
Practical Sensory Exercises
Pouring Nitro Beer practice drill
Observe a nitro pour from first fill through cascade and final top-up; record settling time, bubble movement, head texture, and the difference from a standard draft pour.
Key Terms
- Nitro beer
- Beer served with a nitrogen-rich gas blend for small bubbles, a creamy head, and a smooth texture.
- Restrictor plate
- A small perforated disk in a nitro faucet that forces beer through tiny holes to create the cascade.
- Cascade
- The flow of tiny bubbles in a freshly poured nitro beer that settles into a dense head.