Exam Focus
- Explain that applied CO2 maintains carbonation during dispense.
- Connect temperature, carbonation level, and pressure.
- Recognize overcarbonation and undercarbonation as pressure problems over time.
Carbonation is held, not made, at the keg
Each beer leaves the brewery carbonated to a specific level, usually expressed in volumes of CO2, and the brewer or brand owner should give that target to the retailer. Inside a keg, the CO2 dissolved in the beer and the gas in the headspace settle into equilibrium. Once a coupler connects the keg to a regulator, the applied gas pressure becomes the headspace pressure. If that pressure matches what the beer naturally holds at its temperature, carbonation stays where the brewer set it for the whole life of the keg. The retailer controls the three variables that keep this balance: beer temperature, applied pressure, and gas blend.
How temperature, pressure, and carbonation connect
Cold beer holds more CO2 than warm beer at the same pressure, so one regulator setting is only correct for one combination of carbonation level and temperature. If the cooler runs warmer, the same pressure now holds less gas and the beer slowly gives CO2 up; if it runs colder, the beer slowly absorbs more. Carbonation follows absolute pressure, while draft gauges show gauge pressure. At sea level, absolute pressure is gauge pressure plus about 14.7 psi of atmosphere. At higher elevation the atmosphere contributes less, so a common compensation is to add about 1 psi to the regulator for every 2,000 feet above sea level. Gas blend matters as well: on blended gas, only the CO2 share of the applied pressure holds carbonation, which is why long-draw systems on mixed gas need a blend matched to the beer.
Over and undercarbonation develop over time
| What staff notice | What is happening in the keg | Correction |
|---|---|---|
| Pours are normal at first, then steadily foamier, with a sharper carbonic bite over several days | Applied pressure is above the beer's equilibrium pressure, so the beer absorbs extra CO2 | Return to the correct setting for the beer and temperature; excess CO2 takes time to leave the beer |
| Pours slow down and the beer tastes flatter, with a thin head that fades quickly | Applied pressure is below equilibrium, so CO2 moves out of the beer into the headspace | Restore the correct pressure and check for an empty cylinder or a gas leak |
| Foam starts right after the cooler warmed up | Warmer beer holds less CO2 at the same pressure and breaks out in the line and glass | Fix cooler temperature first; changing pressure only creates a second problem |
Worked application
A direct-draw cooler serves an American lager on 100 percent CO2 and pours well at 38 F. During a busy weekend the staff turn the regulator up to pour faster. For a day or two nothing seems wrong, but by midweek every pour is foamy and the beer tastes prickly. The cause is not the faucet or the glass: the higher pressure pushed extra CO2 into the beer. The fix is to return to the setting that matches the lager's carbonation at 38 F and accept that the keg will need time to settle. Pour speed is a resistance question, not a regulator question.
Why It Matters
- Correct equilibrium pressure keeps a keg from gaining or losing carbonation during service.
- Temperature changes alter the pressure required, so a fixed regulator setting is not universally correct.
- Carbonation maintenance protects flavor, foam, and yield across the life of the keg.
Practical Sensory Exercises
Line-by-line pressure audit
For each draft line you can access, record the beer, its target carbonation from the brewer if available, the cooler temperature, the gas blend, and the regulator setting. Mark any line where one beer shares a regulator with a very different carbonation level, and write what drift you would expect on that line over a week.
Key Terms
- Volumes of CO2
- A measure of carbonation: the volume of CO2 gas dissolved in a given volume of beer.
- Equilibrium pressure
- The applied pressure at which a beer at a given temperature neither gains nor loses CO2.
- Gauge pressure
- Pressure above the surrounding atmosphere, which is what draft regulators display.
- Absolute pressure
- Gauge pressure plus atmospheric pressure; carbonation depends on this value.
- Overcarbonation
- Carbonation above the brewer's target, often caused by applied pressure set too high for the beer's temperature.
- Undercarbonation
- Carbonation below the brewer's target, often caused by applied pressure set too low or a gas supply problem.
- Gas blend
- The mix of CO2 and nitrogen used for dispense; only the CO2 share helps hold carbonation.
References
- US Certified Cicerone® Syllabus v6
- US Certified Cicerone® Syllabus v6 PDF
- Draught Beer Quality Manual, Brewers Association
- Related Certified Cicerone® topic: Draft System Resistance Controls Beer Movement
- Related Certified Cicerone® topic: Applied Gas Pressure and Resistance Determine Flow Rate
- Related Certified Cicerone® topic: Draft System Design