Beer Study Buddy
← Back to syllabus topics

Certified Cicerone® · Keeping and Serving Beer

Draft System Design

Syllabus Path

Draft system design fits pressure, resistance, cooling, and distance together so a specific beer pours at its intended carbonation and flow. Short direct-draw systems can often run on straight CO2, while long-draw systems may need blended gas, beer pumps, FOBs, and glycol cooling. A Certified Cicerone® should explain how the parts fit, recognize when a system needs more than CO2, and tell a design fault from a server technique fault.

  1. I. Keeping and Serving Beer
  2. E. Draft systems
  3. 3. Draft system design

Study Guide

Read the full study guide: Complete Guide to Draft Beer Systems

Exam Focus

  • Explain how system type, distance, pressure, resistance, and cooling fit together.
  • Recognize when long-draw systems need mixed gas or additional hardware.
  • Distinguish design problems from server technique problems.

Design starts from the beer

The beer's carbonation level and serving temperature fix the CO2 pressure needed to hold that carbonation. Everything else in the design is chosen so that pressure produces a pour of about 2 fluid ounces per second. That means the designer has to account for the distance from cooler to bar, the rise or drop in between, how the beer will be kept cold the whole way, and how many lines and kegs the system must serve.

System balance: dynamic and static resistance

Total resistance has two parts. Dynamic resistance comes from friction in beer lines, couplers, shanks, and faucets, and it depends on line length and inside diameter. Static resistance comes from elevation: about 0.5 psi for every foot of rise, with about the same amount given back for each foot of drop. The designer sizes the lines and adds choker tubing or flow-control faucets until total resistance matches the applied pressure. A short direct-draw kegerator may need only about 4 to 5 feet of 3/16-inch vinyl line. A long-draw system has to balance the trunk run, the rise to the bar, and the restriction near the tower.

When long draw needs more than CO2

Long distances and large rises can demand more push than the beer's CO2 equilibrium pressure. Running pure CO2 at that higher pressure would slowly overcarbonate the beer, so long-draw systems often use a CO2 and nitrogen blend: the total pressure is high enough to move the beer, while the CO2 share matches the beer's carbonation. Nitro beers need their own high-nitrogen blend, typically about 25 percent CO2 and 75 percent nitrogen, plus a nitro faucet. Systems with very high resistance may add beer pumps. FOBs reduce the beer lost when a keg empties in a long line, and glycol trunks keep the beer cold over the distance.

Design fault or technique fault?

ClueLikely source
One line has poured foamy for every server since it was installed, even with a correct pourDesign: too little resistance, or no cooling in the tower
Foam appears only when a server opens the faucet partway or pours into a warm or dirty glassTechnique or glassware
A line on mixed gas slowly turns flat or gassy over weeksGas blend not matched to that beer's carbonation
A new, highly carbonated beer foams on a line that pours lager wellDesign mismatch for the new product: pressure, blend, or resistance needs review

Design faults repeat for everyone and from the first day. Technique faults follow the person or the glass.

Why It Matters

  • A balanced design maintains temperature and carbonation while delivering an appropriate flow rate.
  • Early accounting for lift, restriction, cooling, and gas blend prevents chronic foam from being built into the installation.
  • Design literacy lets a beer professional recognize when an operating adjustment cannot fix a structural limitation.

Practical Sensory Exercises

Two-venue design sketch

Sketch two systems: a six-tap kegerator behind the bar, and a 12-tap bar one floor above a basement walk-in about 60 feet away. For each, list the gas supply, cooling type, line type, and any extra hardware such as FOBs or pumps, with one sentence explaining each choice. Do not calculate exact line lengths; focus on why each piece is needed.

Key Terms

System balance
The match between applied pressure and total resistance that gives the intended flow and carbonation.
Dynamic resistance
Friction-based resistance from lines and fittings that exists while beer flows.
Static resistance
Resistance from elevation, about 0.5 psi per foot of rise.
Blended gas
A CO2 and nitrogen mix used so total pressure can rise without overcarbonating the beer.
Beer pump
A pump that adds force on the beer side of high-resistance systems.
FOB (foam on beer detector)
A device that stops flow when a keg empties, saving beer in long lines.
Choker tubing
Narrow restriction line added near the tower to bring total resistance up to the applied pressure.

References

4 available