Study Guide
Read the full study guide: Complete Guide to Draft Beer Systems
Exam Focus
- Maintain cold beer and stable dispense conditions.
- Verify temperature before changing other variables.
- Escalate pressure and hardware changes to trained staff.
Temperature and chilling
A standard draft cooler and system target is about 38 F / 3 C. Kegs should be cold for at least 24 hours before service because a warm keg can foam even after it enters a cold cooler.
Pressure belongs to trained staff
Gas pressure should be set or adjusted by a draft-trained professional. Changing pressure to hide foam can create flat beer, overcarbonated beer, or new balance problems instead of fixing the cause.
Certified Cicerone® Notes
Troubleshooting from symptom to cause
Check beer temperature at the keg and at the faucet first; most pouring problems start there. Then work through the symptom.
| Symptom | Common causes to check |
|---|---|
| No beer at faucet | Empty keg or gas, closed valve, coupler not engaged, FOB not reset, frozen or obstructed line |
| Foaming | Warm beer or warm tower, frozen or kinked line, wrong pressure, failed washers or seals, dirty system, clogged faucet vent |
| Flat beer | Pressure too low for the temperature, gas supply problem, dirty glassware killing the head, very cold beer that releases little CO2 in the glass |
| Cloudy beer | Chill haze from very cold beer, yeast in an unfiltered or end-of-keg pour, or a dirty system |
Servers can check temperature, valves, couplers, empty kegs, and glass cleanliness. Pressure, line length, and glycol settings belong to draft-trained staff, because changing them to hide a symptom usually creates a new problem.
Holding 38 F from cooler to faucet
The syllabus standard is 38 F (3 C), and the goal is the same temperature at every point between keg and glass. Warming anywhere along the way lets CO2 break out of solution and foam at the faucet.
- Kegs need at least 24 hours in the cooler before tapping; a warm keg keeps foaming even after it is connected.
- Direct-draw systems rely on the cooler itself, so check its thermometer and keep the door closed during busy service.
- Air-cooled towers need unobstructed blower airflow through ducts of appropriate length.
- Glycol systems need a running chiller, the correct glycol bath temperature, a working pump return, a clean condenser, and proper glycol strength.
- Measure the beer, not the air: pour a sample and read its liquid temperature at the faucet.
Worked application
When a draft problem appears, verify liquid beer temperature at the keg and faucet before changing pressure. Beer should remain cold and stable from cooler to glass; warm towers, recently delivered warm kegs, or poor glycol performance commonly create foam. Pressure changes made without diagnosis can create overcarbonation or undercarbonation that persists after the original symptom is gone.
Other Certification Notes
Certified Beer Server Open the Certified Beer Server topic page
Exam Focus
- Standard cooler and system temperature is about 38 F / 3 C.
- Kegs should be cold for at least 24 hours before service.
- Gas pressure should be set or adjusted by a draft-trained professional.
Why 38 F and 24 hours matter
Cold beer holds its CO2 well. A draft system's gas pressure is set for beer at about 38 F (3 C), so when beer is warmer than that, CO2 comes out of solution in the line and faucet and the pour turns to foam. A keg that arrives warm chills slowly from the outside in, and how long it takes depends on its size and starting temperature, so the syllabus sets a minimum: every keg should be in the cooler at least 24 hours before service. If a keg still foams after that, the beer's liquid temperature at the faucet is the first thing to check.
| Situation | What happens | What a server does |
|---|---|---|
| Keg tapped soon after delivery | Foamy pours and wasted beer | Tap a keg that has been cold for 24 hours instead |
| Cooler door propped open or overloaded | Temperature drifts up; many taps foam | Close the door, check the thermometer, tell a manager |
| Several taps pour badly at once | A system-wide problem such as temperature or gas | Report it rather than adjusting anything |
What servers check and what they leave alone
A server keeps the system cold and reports problems; a draft-trained professional changes settings.
- Check that the cooler thermometer reads about 38 F (3 C).
- Confirm a new keg has been in the cooler for at least 24 hours before tapping it.
- Never turn the gas regulator: pressure is matched to temperature and carbonation, so too much slowly overcarbonates the beer and too little slowly lets it go flat.
- Work through the basic troubleshooting checks, then call a draft-trained professional if the beer still pours badly.
Why It Matters
- A stable keg-to-faucet process protects carbonation and makes dispense symptoms reproducible.
- Changing pressure without checking temperature and restriction can hide foam briefly while damaging beer over time.
- An operating baseline lets staff identify the exact point where flow, cooling, or gas delivery departed from normal.
Practical Sensory Exercises
Symptom walk-through
For each of the four symptoms in the table, write the first three checks a server can make without changing equipment settings, then the point at which you would call a draft technician.
Key Terms
- Draft-trained professional
- A person trained to set, balance, clean, or repair draft systems safely.
- System temperature
- The beer temperature the draft system is designed to maintain from keg to faucet.
- Applied pressure
- The gas pressure used to maintain carbonation and move beer through the system.
- Draft balance
- Matching applied gas pressure to line resistance so beer pours at the right speed with stable carbonation.
- FOB
- Foam-on-beer detector that stops flow when a keg empties and must be reset after a keg change.
- Gas breakout
- CO2 leaving solution in the line or faucet, usually from warm spots or pressure drops, causing foam.
- Glycol chiller
- Refrigeration unit circulating chilled glycol beside beer lines to keep long-draw beer cold to the faucet.
References
- US Certified Cicerone® Syllabus v6
- US Certified Cicerone® Syllabus v6 PDF
- Draught Beer Quality Manual, Brewers Association
- Related Certified Cicerone® topic: Draft System Components
- Related Certified Cicerone® topic: Types of Cooling Systems
- Related Certified Cicerone® topic: Draft System Design
- Related Certified Cicerone® topic: Draft System Maintenance